Skip to content
AnyRecalls

1996 International Harvester 2574 recalls

Source: NHTSA data as of September 22, 2026. Last refreshed Sep 23, 2026, 2:43 AM UTC.

2 recalls found in NHTSA data as of September 22, 2026

For the 1996 International Harvester 2574. These apply to the model and year, not to one particular vehicle: check your VIN to see whether yours is included and whether it has been repaired.

Has your International Harvester been repaired?

Recalls here come from NHTSA’s records for the model and year. Not every vehicle of a model is included in every recall, and this site can’t see whether a repair has been done. Only a VIN lookup can tell you that.

NHTSA’s VIN search doesn’t show recalls that were already repaired, recalls more than 15 years old, or some small manufacturers’ recalls. A International Harvester dealer can also check your VIN. Recall repairs are free.

1996 International Harvester 2574 recalls, newest first

November 22, 1996NHTSA 96V2330021,133 vehicles potentially affected

Suspension › Rear

Summary
The drive axle housings consist of a plate steel center section and two forged spindles, one of which is welded to each end of the center section. Each spindle contains a keyway slot in which the locking tab for the wheel bearing nut locking mechanism is inserted. The length of the keyway slot may not be long enough to accommodate the tab causing the tab to be deformed or damaged during installation.
Consequence
This locking tab prevents the wheel bearing nut from loosening during vehicle operation. If this tab is deformed, the nut can loosen allowing the wheel to separate from the axle increasing the risk of a vehicle accident.
Remedy
Dealers will replace the drive axle housing nuts with a conventional wheel nut hardware system.

This recall on nhtsa.gov

August 1, 1996NHTSA 96V12400421 vehicles potentially affected

Suspension

Summary
The equalizing beam shaft of the tandem axle suspension were manufactured from as-rolled SAE4140 steel rather than the specified annealed SAE4140. These shafts can fracture inside the beam at the toe of the weld.
Consequence
Vehicles are subject to vehicle tilt and possible rollover in the event that both equalizing beams, on the same side of the vehicle, experience a simultaneous shaft failure. Affected suspensions can also drop and contact the road surface generating sparks which could ignite flammable material.
Remedy
Owner notification is being conducted by neway anchorlok. Dealers will inspect and replace all suspension suspension beams with suspension beams containing appropriate shafts.

This recall on nhtsa.gov

Owner complaints

No owner complaints about the 1996 International Harvester 2574 were found in NHTSA’s complaint data.

Other International Harvester 2574 years

Other 1996 International Harvester models

Most recalled 1996 vehicles

  1. 1996 Dodge Caravan (16 recalls)
  2. 1996 Honda Civic (16 recalls)
  3. 1996 Dodge Ram (14 recalls)
  4. 1996 Plymouth Voyager (13 recalls)
  5. 1996 Chevrolet Cavalier (13 recalls)
All of 1996’s most recalled vehicles

Questions

Does the 1996 International Harvester 2574 have any recalls?
2 recalls found in NHTSA data as of September 22, 2026, covering: suspension. Recalls apply to the model and year; whether a particular vehicle is included, and whether it has been repaired, depends on its VIN.
How do I check if my 1996 International Harvester 2574 recall has been fixed?
Enter your 17-character VIN at nhtsa.gov/recalls, or ask a International Harvester dealer. Recall repairs are free. NHTSA's VIN search doesn't list recalls that were already repaired.
How many complaints have owners filed about the 1996 International Harvester 2574?
0 complaints filed with NHTSA. Complaints are unverified reports from the public that NHTSA uses to decide what to investigate.