Skip to content
AnyRecalls

2006 Mack CTP recalls

Source: NHTSA data as of September 22, 2026. Last refreshed Sep 23, 2026, 2:43 AM UTC.

4 recalls found in NHTSA data as of September 22, 2026

For the 2006 Mack CTP. These apply to the model and year, not to one particular vehicle: check your VIN to see whether yours is included and whether it has been repaired.

Has your Mack been repaired?

Recalls here come from NHTSA’s records for the model and year. Not every vehicle of a model is included in every recall, and this site can’t see whether a repair has been done. Only a VIN lookup can tell you that.

NHTSA’s VIN search doesn’t show recalls that were already repaired, recalls more than 15 years old, or some small manufacturers’ recalls. A Mack dealer can also check your VIN. Recall repairs are free.

2006 Mack CTP recalls, newest first

October 23, 2007NHTSA 07V497000950 vehicles potentially affected

Trailer hitches › Fifth wheel assembly

Summary
On certain trucks equipped with a saf holland simplex fifth wheel, the lever arm pivot bolt may have been over tightened. An over tightened pivot bolt can distort the pivot bolt spacer sleeve, which may prevent the fifth wheel latch jaw from closing and latching securely around the trailer king pin.
Consequence
There is a possibility that the pivot bolt can become loose without the driver's knowledge. When this occurs, the driver could drive away and the trailer could become disengaged, increasing the risk of a crash.
Remedy
Dealers will replace the pivot bolt and sleeve with a hex head shoulder bolt and washer free of charge. The recall began on January 28, 2008. Owners may contact mack trucks at 1-800-528-6586.

This recall on nhtsa.gov

August 15, 2007NHTSA 07V36100021,847 vehicles potentially affected

Service brakes, air › Supply › Check valve

Summary
On certain trucks equipped with parker single check valves (scv) provided by bendix. The defect exists in the parker scv that connects with the supply port of the SR-7 spring brake modulating valve. After prolonged use of the parker scv, the valve body retainer may become excessively worn and eventually break apart. Pieces of the parker scv can become lodged inside the SR-7 spring brake modulating valve, potentially causing either leakage out of the SR-7 valve or preventing air from properly exhausting from the SR-7 valve.
Consequence
This condition can cause a delay in the application of the spring brakes to park the vehicle after the operator pulls the dash valve button. These conditions can occur without warning, leading to unintended vehicle rollaway, brake drag, or in the case of loss of primary circuit, inability to modulate the spring brakes.
Remedy
Mack is working with bendix to replace the parker single check valve. The recall began on January 9, 2008. Owners may contact bendix at 1-440-329-9000 or mack at 1-800-528-6586.

This recall on nhtsa.gov

August 15, 2007NHTSA 07V36000018,805 vehicles potentially affected

Parking brake

Summary
On certain trucks equipped with bendix SR-7 spring brake modulating valves, the internal rubber check valve may leak causing a delay in the application of the spring brakes to park the vehicle after the operator pulls the dash valve button.
Consequence
This could delay or failure in applying the parking brakes which could result in a vehicle roll away, increasing the risk of a crash.
Remedy
Mack is working with bendix to repair these vehicles (please see 07E037). Bendix will install a check valve repair kit for the affected SR-7 spring brake modulating valve free of charge. The recall began on January 10, 2008. Owners may contact bendix at 1-440-329-9000 or mack at 1-800-528-6586.

This recall on nhtsa.gov

March 14, 2007NHTSA 07V0980003,587 vehicles potentially affected

Service brakes, hydraulic › Pedals and linkages

Summary
On certain trucks, the cotter pin that retains the brake pedal clevis pin may not have been installed. The clevis pin connects the brake pedal to the brake foot valve.
Consequence
If the pin were to come loose, the driver would not be able to apply the service brake, which could result in a crash.
Remedy
Dealers will inspect to see if the cotter pin is missing. If the pin is missing, the cotter pin will be installed. Owners are being advised not the drive the vehicle until the pin has been installed. The recall began on March 26, 2007. Owner may contact mack truck at 1-800-528-6586.

This recall on nhtsa.gov

Owner complaints

No owner complaints about the 2006 Mack CTP were found in NHTSA’s complaint data.

Other Mack CTP years

Other 2006 Mack models

Most recalled 2006 vehicles

  1. 2006 Ford E-350 (39 recalls)
  2. 2006 Ford E-250 (31 recalls)
  3. 2006 Thomas Built Buses Minotour (22 recalls)
  4. 2006 Freightliner Columbia (21 recalls)
  5. 2006 Thomas Built Buses SAF-T-Liner C2 (21 recalls)
All of 2006’s most recalled vehicles

Questions

Does the 2006 Mack CTP have any recalls?
4 recalls found in NHTSA data as of September 22, 2026, covering: trailer hitches, service brakes, air, parking brake, service brakes, hydraulic. Recalls apply to the model and year; whether a particular vehicle is included, and whether it has been repaired, depends on its VIN.
How do I check if my 2006 Mack CTP recall has been fixed?
Enter your 17-character VIN at nhtsa.gov/recalls, or ask a Mack dealer. Recall repairs are free. NHTSA's VIN search doesn't list recalls that were already repaired.
How many complaints have owners filed about the 2006 Mack CTP?
0 complaints filed with NHTSA. Complaints are unverified reports from the public that NHTSA uses to decide what to investigate.