Skip to content
AnyRecalls

2000 Kenworth W900 recalls

Source: NHTSA data as of September 22, 2026. Last refreshed Sep 23, 2026, 2:43 AM UTC.

9 recalls found in NHTSA data as of September 22, 2026

For the 2000 Kenworth W900. These apply to the model and year, not to one particular vehicle: check your VIN to see whether yours is included and whether it has been repaired.

Has your Kenworth been repaired?

Recalls here come from NHTSA’s records for the model and year. Not every vehicle of a model is included in every recall, and this site can’t see whether a repair has been done. Only a VIN lookup can tell you that.

NHTSA’s VIN search doesn’t show recalls that were already repaired, recalls more than 15 years old, or some small manufacturers’ recalls. A Kenworth dealer can also check your VIN. Recall repairs are free.

2000 Kenworth W900 recalls, newest first

April 1, 2003NHTSA 03V125000154 vehicles potentially affected

Suspension › Front › Hub

Summary
On certain trucks equipped with truck hub units manufactured by skf exclusively for use on arvinmeritor's FF98X series non-drive steer axles, the hub unit bearings can wear prematurely.
Consequence
Seizure of the bearings can cause wheel separation or wheel end fire.
Remedy
Dealers will replace all front axle hubs. Notification began July 16, 2003. The manufacturer has advised us that parts will not be available until September 2003. Owners who take their vehicles to an authorized dealer on an agreed upon service date and do not receive the free remedy with a reasonable time should contact peterbilt at 940-591-4201 or kenworth 425-828-5440.

This recall on nhtsa.gov

July 15, 2002NHTSA 02V0370034,513 vehicles potentially affected

Steering › Linkages › Tie rod assembly

Summary
Heavy duty trucks equipped with TRW tie rod ends on certain arvinmeritor and dana axles. Peterbilt will recall 1,434 vehicles equipped with arvinmeritor axles manufactured from December 11, 1999, to may 14, 2000, and from July 22 to September 30, 2000. Kenworth will recall 859 vehicles equipped with arvinmeritor vehicles manufactured from December 11, 1999, to may 23, 2000, and from July 27, 2000, to September 30, 2000 and kennworth will recall an additional 4,151 vehicles equipped with dana axles and manufactured from June 23 to December 6, 1999, and from may 23 to September 30, 2000. The tie rod and drag link ball stud ends contain bearings that are below the specified case depth and/or hardness.
Consequence
This can lead to premature wear with possible separation of the ball stud from the socket, increasing the risk of loss of control of the vehicle.
Remedy
Dealers will remove and replace all affected tie rods and drag links with different designed ends. Owner notification began July 15, 2002. Owners who take their vehicles to an authorized dealer on an agreed upon service date and do not receive the free remedy within a reasonable time should contact peterbilt at 1-940-591-4201 or kenworth at 1-425-828-5440.

This recall on nhtsa.gov

February 27, 2002NHTSA 02V061001116 vehicles potentially affected

Suspension › Rear

Summary
On certain heavy duty trucks equipped with replacement dana spicer tandem drive axle models DS463 and DS521, installed on vehicles from may 1, 2001 through February 1, 2002, an undersized attachment weld may fracture without warning.
Consequence
The loss of this attachment to the vehicle chassis can adversely affect vehicle handling or driver control.
Remedy
Dana is conducting the owner notification and remedy for this campaign. The dealers will remove the suspect bracket, inspect the axle housing, and reweld the bracket to the axle housing. Owners who take their vehicles to an authorized dealer on an agreed upon service date and do not receive the free remedy within a reasonable time should contact dana at 616-567-1088 or kenworth at 425-828-5440.

This recall on nhtsa.gov

February 4, 2002NHTSA 02V03300044 vehicles potentially affected

Electrical system › Wiring

Summary
On some heavy duty trucks equipped with alcoa fujikura ltd. (afl) power distribution boxes (pd box), the pd boxes were manufactured with insufficient torque applied to the nut of the main power feed-through stud.
Consequence
Insufficient torque can lead to (1) electrical arcing of the wires inside of the pd box, or (2) an interrupted power supply to the vehicle's electrical system, either of which can lead to a loss of vehicle electrical power and possibly vehicle control without warning.
Remedy
Dealers will inspect and tighten the nut on the main power feed-through stud. Owner notification began February 25, 2002. Owners who take their vehicles to an authorized dealer on an agreed upon service date and do not receive the free remedy within a reasonable time should contact kenworth at 1-425-828-5440.

This recall on nhtsa.gov

August 28, 2001NHTSA 01V1400062,294 vehicles potentially affected

Steering › Linkages › Tie rod assembly

Summary
Vehicle description: heavy duty trucks equipped with TRW tie rod ends on certain meritor axles. The tie rod and drag link ball stud ends contain bearings that are below the specified case depth and/or hardness.
Consequence
This can lead to premature wear with possible separation of the ball stud from the socket, increasing the risk of loss of control of the vehicle.
Remedy
Dealers will remove and replace all affected tie rods and drag links with different designed ends. Owner notification began October 24, 2001. Owners who take their vehicles to an authorized dealer on an agreed upon service date and do not receive the free remedy within a reasonable time should contact peterbilt at 1-940-591-4000 or kenworth at 1-425-828-5000.

This recall on nhtsa.gov

May 17, 2001NHTSA 01V167001390 vehicles potentially affected

Suspension

Summary
Vehicle description: heavy duty trucks equipped with chalmers 1000 series and 800 series suspension kits. These suspension kits may have insufficient penetration of the weld attaching the torque rod eye to the torque rod tube.
Consequence
Failure of the weld could result in separation of the eye and tube, causing a lock of axle retention, which could result in loss of vehicle control.
Remedy
Dealers will replace all chalmers fixed torque rods on these vehicles. Owner notification began July 27, 2001. Owners who take their vehicles to an authorized dealer on an agreed upon service date and do not receive the free remedy within a reasonable time should contact peterbilt at 1-940-591-4000 or kenworth at 1-425-828-5000.

This recall on nhtsa.gov

April 24, 2001NHTSA 01V14200014 vehicles potentially affected

Equipment › Other › Labels

Summary
Vehicle description: heavy duty trucks equipped with meritor FG941 steer axles. The gross axle weight rating (GAWR) was determined incorrectly and over-stated on the vehicle certification label. With the incorrect GAWR listed, these labels do not meet the certification requirements of part 567, "requirements for manufacturers of motor vehicles." vehicles will be remedied either by assigning the proper weight rating or, if possible, by changing the necessary components to meet the currently assigned weight rating.
Consequence
These vehicles would not be in compliance with federal regulations.
Remedy
Vehicles will be remedied either by assigning the proper weight rating or, if possible, by changing the necessary components to meet the currently assigned weight rating. Owner notification began June 22, 2001. Owners who take their vehicles to an authorized dealer on an agreed upon service date and do not receive the free remedy within a reasonable time should contact kenworth at 1-425-828-5000.

This recall on nhtsa.gov

February 20, 2001NHTSA 01V051000209 vehicles potentially affected

Suspension › Front › Control arm › Lower arm

Summary
Vehicle description: vehicles equipped with 54" rear axle spacing configuration of the airglide 200 suspension with the service application identified as logger, dump truck, or tanker. The rear suspension is regularly subjected to extreme articulation, resulting in flexing of the joint.
Consequence
Failure of the lower sway arm attaching bolts could result in loss of vehicle control.
Remedy
Dealers will replace the lower sway arm brackets. Owner notification began March 27, 2001. Owners who take their vehicles to an authorized dealer on an agreed upon service date and do not receive the free remedy within a reasonable time should contact kenworth at 1-425-828-5000.

This recall on nhtsa.gov

February 5, 2001NHTSA 01V0210001,992 vehicles potentially affected

Electrical system › Wiring › Fuses and circuit breakers

Summary
Vehicle description: heavy duty trucks equipped with an optional firewall-mounted circuit breaker. The main cab power and battery power leads were attached incorrectly. This condition can result in the main cab power being unprotected.
Consequence
If a wiring short occurred anywhere along the cab power circuit, the available battery power could arc and cause subsequent damage to the vehicle or a fire.
Remedy
Dealers will inspect and correct the problem, as needed. Owner notification began February 26, 2001. Owners who take their vehicles to an authorized dealer on an agreed upon service date and do not receive the free remedy within a reasonable time should contact kenworth at 1-425-828-5000.

This recall on nhtsa.gov

Owner complaints

Owners have filed 7 complaints about the 2000 Kenworth W900 with NHTSA. Complaints are unverified reports from the public; NHTSA uses them to decide what to investigate.

Crashes reported
0
Fires reported
0
Injuries reported
0
Deaths reported
0

Most complained-about components

  1. Suspension2
  2. Air › Antilock1
  3. Electrical system1
  4. Engine and engine cooling › Engine › Gasoline1
  5. Power train › Manual transmission1

Other Kenworth W900 years

Other 2000 Kenworth models

Most recalled 2000 vehicles

  1. 2000 Honda Accord (21 recalls)
  2. 2000 Chevrolet Silverado (19 recalls)
  3. 2000 Honda Civic (18 recalls)
  4. 2000 Ford Focus (17 recalls)
  5. 2000 Ford F-150 (17 recalls)
All of 2000’s most recalled vehicles

Questions

Does the 2000 Kenworth W900 have any recalls?
9 recalls found in NHTSA data as of September 22, 2026, covering: suspension, steering, electrical system, equipment. Recalls apply to the model and year; whether a particular vehicle is included, and whether it has been repaired, depends on its VIN.
How do I check if my 2000 Kenworth W900 recall has been fixed?
Enter your 17-character VIN at nhtsa.gov/recalls, or ask a Kenworth dealer. Recall repairs are free. NHTSA's VIN search doesn't list recalls that were already repaired.
How many complaints have owners filed about the 2000 Kenworth W900?
7 complaints filed with NHTSA. Complaints are unverified reports from the public that NHTSA uses to decide what to investigate.